Fovea: IP Video Analyser
- ?Real World? Viewer Simulation.
- Multicast IPTV
- Video on Demand.
- Emulates up to 500 Unique Viewers on (2) 1GbE ports.
- Measures Viewer Quality of Experience.
- MPEG-2 transport stream packet metrics.
- Video stream measurements.
- Perceptual video quality.
- Channel change and video presentation times.
- VoD response times.
Allegro
- Low-cost, portable-sized units for network testing, travel or low-line count applications in the lab.
- Supports T1/E1, POTS and IP interfaces.
- Allegro products operate similarly with much smaller line counts and are used in smaller developer test beds, customer support applications, in network testing scenarios or when lower cost products are desired.
- E1/T1 using SS7, PRI and CAS.
- IP using SIP and MGCP.
- POTS using loop and ground start.
Fortissimo
- 19-inch, 1RU modules for lab environments and high capacity testing.
- Supports OC3/STM1, DS3, T1/E1, IP, POTS and DECT interfaces.
- Fortissimo products simulate large volumes of telephony traffic over PSTN and IP interfaces using common signaling protocols.
- They are most typically used in lab environments and when high subscriber counts are needed.
- STM1/OC3, DS3, E1/T1, using SS7, PRI and CAS signaling.
- IP using SIP and MGCP signaling.
- POTS using loop and ground start signaling.
- DECT wireless.
Sage 960B
- The 960B combines TDM, Ethernet, and Analog interfaces with unparalleled "Real-Time" simultaneous test capability to comprehensively test and monitor Next Generation Elements and Networks.
- Supports 2-wire, 4-wire, ISDN PRI and SIP calls with voice quality measurement and SLA verification.
- Measures MOS and R-factor.
- Voice Processing & IP Telephony Transparency Testing.
- VoIP Service Pre-Qualification, Turn-Up Testing, and Troubleshooting.
- IMS VoIP & Video Certification.
- Echo Cancellation Performance.
- Measures background noise.
DSL Loop simulators: Multi-Standard Local Loop Simulators
- Ideal for testing ADSL, ADSL2, ADSL2+, VDSL2 chips/modems/DSLAMs
- Simulates 0.4mm PE per ETSI TS 101 388 and TP100 per ETSI TS 101 270-1 & G.992.5 Annex M,
- Loop lengths programmable from 0 to 9,000 m in 10-m increments.
TX130/e+: Handheld Multifunctional E1 tester
- Tests E1, Ethernet, E3/DS3 and Datacom in a single tool.
- Robust, handheld chassis with large colour touch screen LCD display.
- Supports dual balanced (120O) and Unbalanced (75O) interfaces for E1.
- Non-intrusive Pulse Mask Analysis at E1 DS1, and E3, DS3 bit rates.
- Tests ISDN PRI and Voice Frequency channels.
- Supports 10/100/1000 Base -T test interface for Layer 2, 3 and 4 BER, RFC2544 and Throughput measurements.
- Generates traffic with VLAN and MPLS headers.
- Supports V.35, X.21, RS-449, RS-232 DTE/DCE simulation.
- Jitter measurement per ITU-T O.171.
BX 100V
- Supporting both xTU-C and xTU-R modes for VDSL2 and ADSL2+ service installations.
- Impulse Noise Protection (INP) for IPTV applications is supported while Packet Transfer Mode (PTM) provides next generation Triple Play service flows in pass through mode.
- CPE and CO Emulation.
- Fast display of link-up results: upstream/downstream data rates, noise margin, latency, attenuation, training time, PSD, INP, vendor ID, profile, interleave delay, interleave depth.
- Graphical and tabular representation of bits per tone with unique Bitstogram to identify DSL line degradation.
- FEC, HEC and code violation count for upstream and downstream paths.
- Terminate, Pass-Through and Terminal Equipment test modes.
- Annex M support.
- Impulse Noise Protection (INP) support.
- Advanced IP connectivity test functions over ADSL interface.
- IPTV stream analysis: MPEG2, MPEG4 Part 10 (H.264) and VC-1 in ADSL Terminate mode (modem emulation).
- IGMP latency (channel zapping), Media Delivery Index (MDI) and Primary Clock Reference (PCR), and jitter measurements.
- NetWiz cable diagnosis with network statistics.
- VoIP call emulation and MOS performance analysis.
- WiFi Wiz site survey with Internet connection test.